Integy Motor Mount II problem

Ze-tung · #1 03-13-2002, 02:17 PM

Recently, i purchased integy's motor mount 2...and while driving it, I lost one of the dang screws that holds it into the chasis....the stock ones don't fit....Soooooo

Can anyone here give me the dimension for these countersunk screws??? I've tried contacting the place I got it from, but they don't know...

HELP! I CAN'T DRIVE IT UNTIL I GET THESE DANG SCREWS!!

Whatup1049p · #2 03-13-2002, 02:25 PM

Same ting happend to me man

I found some countersunk screws that were too long so i cut them shorter and they work perfect. This time I put threadlock on them

Whatup1049-

Ze-tung · #3 03-13-2002, 03:03 PM

do you happen to recall the specs of those screws?

Whatup1049p · #4 03-13-2002, 03:35 PM

No sorry i basically found them in my box of junk parts. I know you can get them at hardware stores though

Whatup1049-

Woody · #5 03-13-2002, 04:01 PM

I'm not familiar with that set-up. Is it for the Big block? If it is, it should be a 4mm. If it is for the stock set up it should be a 2mm.

other_cents · #6 03-13-2002, 05:53 PM

I think Integy was using american screws. I had to retap the screw holes to get anything to work.

Ze-tung · #7 03-13-2002, 06:10 PM

-To Woody

No, it's the standard integy motor mount II....It only fits the stock motor, and others such as orion's micro modified....You can check out any site that sells them....and in every one, they have a picture of the screws that are included....but NO specs on them!!

Woody · #8 03-13-2002, 11:15 PM

OK, do you have a pic of the one you've got? Most good hardware stores have thread"pitch"finders. A "pitch" finder is a gauge that they use to find the size of thread that you need.
I should have read more thoroughly. I'll look around and see what I can find for you. In the meantime, maybe yourmicro might know since they have Integy parts in the shop.

TGRupert · #9 03-14-2002, 07:42 AM

Guys, lets try to put things in the right place, the main section is HUGE. this should go in the parts and hop-ups section.

Woody · #10 03-14-2002, 11:31 AM

OK, I've got it. I'm pretty sure it's a 4-40 screw. Hopefully it works out for you, let us know......

Ze-tung · #11 03-14-2002, 04:03 PM

Thanks woody, I'll try that...and let you know how it works out...

hum....sorry for putting this string in the "wrong" place---practically every string in the general area involve "parts" and "hop ups"---Is it really your place to tell people where they can post questions?

TGRupert · #12 03-14-2002, 04:50 PM

I had yourmicro create the parts section just a couple of days ago for the reason that

Quote:

practically every string in the general area involve "parts" and "hop ups"

Quote:

Is it really your place to tell people where they can post questions?

I was just trying to get the word out to use the new section because I'm sick of the main section being full of tons of stuff and not being able to find the posts i'm looking for. I'm REALLY sorry if I came off as rude at all the section hadn't been there for even 24 hours and I didn't expect everyone to know. I posted the exact same message to several other threads about parts in the gereralk section.

Ze-tung · #13 03-14-2002, 08:49 PM

oh...sorry....i can never tell what people mean on these things...

so what is the general discussion supposed to be used for then?? this is confusing.

xxtcrgp · #14 03-14-2002, 08:54 PM

its used for if you have problems with turning radius, taking the rims off, e.t.c.

TGRupert · #15 03-16-2002, 04:49 PM

Quote:

Originally posted by Ze-tung
oh...sorry....i can never tell what people mean on these things...

so what is the general discussion supposed to be used for then?? this is confusing.

it's used for anything that doesn't fit anywhere else. or stuff like "why I love my micro" or a thread abouyt standard stock class rules.