YourMicro.com - HPI Micro RS4, Losi Mini-T, XRay M18, Forums, News, Pictures, Parts, and Shop
Forums, M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
M18 Hop-Ups, M18 Parts, Mini-LST Hop-Ups, Mini-LST Parts, Kyosho, Atomic, 3Racing, Country Alloy Works, Castle Creations, Trinity, Intellect, United RC, Battery Packs, 2/3A
  #1  
Old 03-13-2002, 02:17 PM
Ze-tung Ze-tung is offline
Micro Novice
 
Join Date: Feb 2002
Location: IN
Posts: 27
Integy Motor Mount II problem

Recently, i purchased integy's motor mount 2...and while driving it, I lost one of the dang screws that holds it into the chasis....the stock ones don't fit....Soooooo

Can anyone here give me the dimension for these countersunk screws??? I've tried contacting the place I got it from, but they don't know...

HELP! I CAN'T DRIVE IT UNTIL I GET THESE DANG SCREWS!!
Reply With Quote
  #2  
Old 03-13-2002, 02:25 PM
Whatup1049p Whatup1049p is offline
Micro Master
 
Join Date: Feb 2002
Posts: 116
Same ting happend to me man I found some countersunk screws that were too long so i cut them shorter and they work perfect. This time I put threadlock on them

Whatup1049-
Reply With Quote
  #3  
Old 03-13-2002, 03:03 PM
Ze-tung Ze-tung is offline
Micro Novice
 
Join Date: Feb 2002
Location: IN
Posts: 27
do you happen to recall the specs of those screws?
Reply With Quote
  #4  
Old 03-13-2002, 03:35 PM
Whatup1049p Whatup1049p is offline
Micro Master
 
Join Date: Feb 2002
Posts: 116
No sorry i basically found them in my box of junk parts. I know you can get them at hardware stores though

Whatup1049-
Reply With Quote
  #5  
Old 03-13-2002, 04:01 PM
Woody's Avatar
Woody Woody is offline
Macho Gabacho
 
Join Date: Feb 2002
Location: Colorado
Posts: 860
I'm not familiar with that set-up. Is it for the Big block? If it is, it should be a 4mm. If it is for the stock set up it should be a 2mm.
__________________
www.americanracingmodels.com
IT'S BETTER TO LOOK GOOD THAN ACTUALLY BE GOOD.....
Reply With Quote
  #6  
Old 03-13-2002, 05:53 PM
other_cents other_cents is offline
Micro Master
 
Join Date: Feb 2002
Location: Denver, CO
Posts: 84
Send a message via ICQ to other_cents
I think Integy was using american screws. I had to retap the screw holes to get anything to work.
Reply With Quote
  #7  
Old 03-13-2002, 06:10 PM
Ze-tung Ze-tung is offline
Micro Novice
 
Join Date: Feb 2002
Location: IN
Posts: 27
-To Woody

No, it's the standard integy motor mount II....It only fits the stock motor, and others such as orion's micro modified....You can check out any site that sells them....and in every one, they have a picture of the screws that are included....but NO specs on them!!
Reply With Quote
  #8  
Old 03-13-2002, 11:15 PM
Woody's Avatar
Woody Woody is offline
Macho Gabacho
 
Join Date: Feb 2002
Location: Colorado
Posts: 860
OK, do you have a pic of the one you've got? Most good hardware stores have thread"pitch"finders. A "pitch" finder is a gauge that they use to find the size of thread that you need.
I should have read more thoroughly. I'll look around and see what I can find for you. In the meantime, maybe yourmicro might know since they have Integy parts in the shop.
__________________
www.americanracingmodels.com
IT'S BETTER TO LOOK GOOD THAN ACTUALLY BE GOOD.....
Reply With Quote
  #9  
Old 03-14-2002, 07:42 AM
TGRupert TGRupert is offline
AWOL
 
Join Date: Feb 2002
Location: NEW YORK
Posts: 1,971
Send a message via AIM to TGRupert
Guys, lets try to put things in the right place, the main section is HUGE. this should go in the parts and hop-ups section.
__________________
why did you turn vb code off? did someone deside to hack the board or somthing?
Reply With Quote
  #10  
Old 03-14-2002, 11:31 AM
Woody's Avatar
Woody Woody is offline
Macho Gabacho
 
Join Date: Feb 2002
Location: Colorado
Posts: 860
OK, I've got it. I'm pretty sure it's a 4-40 screw. Hopefully it works out for you, let us know......
__________________
www.americanracingmodels.com
IT'S BETTER TO LOOK GOOD THAN ACTUALLY BE GOOD.....
Reply With Quote
  #11  
Old 03-14-2002, 04:03 PM
Ze-tung Ze-tung is offline
Micro Novice
 
Join Date: Feb 2002
Location: IN
Posts: 27
Thanks woody, I'll try that...and let you know how it works out...

hum....sorry for putting this string in the "wrong" place---practically every string in the general area involve "parts" and "hop ups"---Is it really your place to tell people where they can post questions?
Reply With Quote
  #12  
Old 03-14-2002, 04:50 PM
TGRupert TGRupert is offline
AWOL
 
Join Date: Feb 2002
Location: NEW YORK
Posts: 1,971
Send a message via AIM to TGRupert
I had yourmicro create the parts section just a couple of days ago for the reason that
Quote:
practically every string in the general area involve "parts" and "hop ups"
Quote:
Is it really your place to tell people where they can post questions?
I was just trying to get the word out to use the new section because I'm sick of the main section being full of tons of stuff and not being able to find the posts i'm looking for. I'm REALLY sorry if I came off as rude at all the section hadn't been there for even 24 hours and I didn't expect everyone to know. I posted the exact same message to several other threads about parts in the gereralk section.
__________________
why did you turn vb code off? did someone deside to hack the board or somthing?

Last edited by TGRupert; 03-14-2002 at 04:52 PM.
Reply With Quote
  #13  
Old 03-14-2002, 08:49 PM
Ze-tung Ze-tung is offline
Micro Novice
 
Join Date: Feb 2002
Location: IN
Posts: 27
oh...sorry....i can never tell what people mean on these things...

so what is the general discussion supposed to be used for then?? this is confusing.
Reply With Quote
  #14  
Old 03-14-2002, 08:54 PM
xxtcrgp's Avatar
xxtcrgp xxtcrgp is offline
Registered User
 
Join Date: Feb 2002
Location: Canada
Posts: 1,785
its used for if you have problems with turning radius, taking the rims off, e.t.c.
__________________
-----Grant
Reply With Quote
  #15  
Old 03-16-2002, 04:49 PM
TGRupert TGRupert is offline
AWOL
 
Join Date: Feb 2002
Location: NEW YORK
Posts: 1,971
Send a message via AIM to TGRupert
Quote:
Originally posted by Ze-tung
oh...sorry....i can never tell what people mean on these things...

so what is the general discussion supposed to be used for then?? this is confusing.
it's used for anything that doesn't fit anywhere else. or stuff like "why I love my micro" or a thread abouyt standard stock class rules.
__________________
why did you turn vb code off? did someone deside to hack the board or somthing?
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 07:41 AM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2007 YourMicro.com
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts